Sika ® Rugasol ® G
Sika ® Rugasol ® G is a kind of economical type retarder, the surface of concrete or mortar is used to override docking in plaster, epoxy floor paint, or other concrete layer.After concrete or mortar after curing, the surface cleaning, aggregate will be exposed.This process is need to sandblast or rough surface.Can also be used for ornamental exposed aggregate surface treatment
- Easy to brush or spray
- A single construction
- Reduce the cost of expensive coarse grinding
- Reduce labor costs
- Provide a good mechanical properties
- Consensus building adornment effect
Using range
- Apply on seam baffle
- Used for floor floor, driveway, swimming pool floors, the decorative surface of the pavement
Feature/advantages
- Easy to brush or spray
- A single construction
- Reduce the cost of expensive coarse grinding
- Reduce labor costs
- Provide a good mechanical properties
- Consensus building adornment effect
packaging
20 L buckets
color
Pale yellow gel
Technical information
The best life
Since the production within six months
Storage conditions
Products to original preservation in 30 ° C + 5 ° C to + dry environment.Avoid direct sunlight.
applied
The dosage
Fresh concrete in construction
Concrete type |
Suggested dilution Sika ® Rugasol ® G coverage |
Use of concrete retarder (usually the C30 and below) |
0.6 1.2 l/m squared * |
Use only the super plasticity agent or only use super gentle admixture of concrete plasticity agent (usually the C35 and above) |
1.0 2.0 l/m squared |
* suggest that preliminary experiment was carried out to determine the actual coverage
Coverage may be related to suggest that the coverage of different type (due to cement, cement content, environmental temperature and Sika ® Rugasol ® G before removing the duration of the stay on concrete).Therefore, it is recommended that a preliminary test to determine the actual coverage in the concrete, etching depth and from the concrete surface to remove the duration of the soft floating cement slurry before/waiting time
Apply on the surface of the template
0.20 0.30 l/m squared (do not dilute)
applied
Construction in the new pouring concrete
Pouring concrete
In a normal way of concrete pouring and compaction.Then the spatula to erased
The construction of the
Sika ® Rugasol ® G: water = 1:2 mixed thoroughly.Stable solution can be obtained
After water seepage in the concrete dry, before the initial solidification, immediately with low pressure spray container will dilute the Sika ® Rugasol ® G directly sprayed on the surface of concrete.Pay attention to the coating thickness should be consistent note: dilute Sika ® Rugasol ® G do not apply on the template
remove
After the initial curing of concrete (need) for 24 hours in warm weather, soft floating cement slurry can be used on the surface of the bristle brush or steel wire brush wash and brush off, or clean with injection pressure (bar), 150-200 to make the aggregate show.Suggestions for large area (> 50 m squared) high pressure water cleaning.Remove soft floating cement slurry to expose bare aggregate process must be completed before the surface hardening
Note: exposure depth may be due to concrete cement content, environmental temperature, Sika ® Rugasol ® G dosage and remove before lien on the surface of the concrete time.However, etching depth is about 3-5 mm to normal status.Suggest that preliminary experiment was carried out
Apply on the surface of the template
hybrid
Sika ® Rugasol ® G as ready-to-use products, not diluted
The construction of the
Template need to clean and do not contain any release agent.Sika ® Rugasol ® G can use brush or a short version of the drum of the construction.Evenly applied thoroughly to achieve uniformity of etching depth.Sika ® Rugasol ® G after construction to avoid direct sunlight.Before concrete pouring, Sika ® Rugasol ® G must be completely dry without sticky.Sika ® Rugasol ® G to avoid contact with moisture or water during drying
remove
For best results, after the concrete enough strength should remove templates and mould as soon as possible.Generally mild weather about 24 to 48 hours.Can bristle brush, wire brush or high pressure water column (150-200 bars) scrubbing surface to aggregate.Mold removal will be slightly soft floating cement slurry adhesion, before hardening can easily from the template and concrete on washing brush.Remove enough please immediately clean the mold, because the soft floating pulp can rapid hardening cement.